neunpara Posted October 3, 2008 Posted October 3, 2008 Hallo, darf man in der Production den Kunstoffgriff seiner Waffe stippeln? Ich habe im Regelwerk keine eindeutige Antwort gefunden. Gruß Volker
Iggy Posted October 4, 2008 Posted October 4, 2008 Hallo, darf man in der Production den Kunstoffgriff seiner Waffe stippeln? Ich habe im Regelwerk keine eindeutige Antwort gefunden.Gruß Volker Hi folks,As there seems to be yet another burst of "Can I .... ?" questions in respect of Production Division, I think it's time for all of us to revisit the (now expanded) FAQ I wrote, which has one change from "No" to "Yes" (and, God, I hate when that happens!): 1. Magazines & Magwells: 01. Can I add aftermarket rubber or "deresonator" pads to the base of my magazines, just for protection, not to increase capacity? 02. Can I add weights to the bottom of my OFM magazines, provided they don't increase capacity? 03. Can I use aftermarket springs in my OFM magazines, provided they don't increase capacity? 04. Can I paint, flare, file, enlarge and/or shave the inside of my magwell? 05. Can I paint the inside of my magwell so that I have something to aim at when reloading? 06. Can I bolt-on a magwell like the H&K "Jet Funnel", or the one from the S&W Performance Center? 07. Can I remove the magwell from my Tanfoglio Stock Custom / H&K USP Production and be legal? 08. Can I change or cut the spring and/or follower in my OFM magazines? 09. Can I use a +1 follower in my OFM magazines? 10. Can I remove the magazine insert from my Glock magazines? 11. Can I use the +2 basepads which were already fitted to my Glock mags when I bought them from my local dealer? 12. Can I make my own flat basepads for my Glock to replace the original Glock +2 basepads which came with my gun? 13. Can I use +2 basepads in my Glock if I only load 17 rounds? 14. Can I use Glock 17 magazines in my Glock 19? 15. Can I use Glock 18 (31/33 round) magazines in my Glock 17? 16. Can I use Glock 22 mags (.40 cal) in my Glock 31 (.357)? 17. Can I use an original 20 round magazine in my Beretta 92FS? 18. Can I use SIG 20 round magazines in my P226? 19. Can I use CZ75 SP01 magazines in my CZ75B? 2. Modifications or Embellishments to Slides and Frames: 01. Can I have my slide re-blued or hard chromed by my local gun shop? 02. Can I have zebra stripes / leopard spots / Kermit The Frog green added to my gun? 03. Can I apply swimming pool paint / cement paint to my gun? 04. Can I "bead-blast" the slide of my gun? 05. Can I paint a stripe down the length of my slide? 06. Can I shave the rear of my gun frame? 07. Can I engrave my name on the side of my gun? 08. Can I add lightening cuts to the slide of my gun? 09. Can I personally modify my G17 frame in order to fit the Oval Extended Magazine Catch? 10. Can I use an aftermarket stainless/aluminium/titanium/unobtainium frame on my Glock? 11. Can I add a stick-on recoil dampener to the rear of the backstrap on my Glock? 12. Can I add a beaver tail (like a "Glocktail") to prevent side bite? 3. Internal and External Modifications: 01. Can I insert a plastic "butt-plug" in my Glock? 02. Can I insert a "Seattle Slug" in my Glock? 03. Can I add some weight inside the back channel of my Glock grip? 04. Can I use a Jentra "overtravel trigger stop" in my Glock? 05. Can I have a "trigger job" done on my gun, or can I do one myself? 06. Can I remove the slide stop, slide lock (or the outer portion thereof) from my Glock? 07. Can I grind some material off my hammer? 08. Can I use an aftermarket connector in my Glock? 09. Can I use my 135mm threaded barrel in my Glock? 10. Can I attach a light / bayonet / laser / can opener to the front rail of my Glock? 11. Can I use a titanium or unobtanium recoil guide rod in my Glock? 12. Can I use a BarSto or Jarvis barrel in my Glock? 13. Can I install a manual thumb safety on my Glock 17? 14. Can I or my local gunsmith install the oval magazine release on my Glock? 15. Can I shave the feed ramp of my Beretta 92FS? 16. Can I shave the front of my trigger so that I can reach it more easily? 17. Can I use recoil buffs in my gun? 18. Can I drill or cut my trigger guard so that it fits my holster? 19. Can I cut or otherwise modify my OFM recoil guide rod and/or spring? 20. Can I use an aftermarket recoil guide rod and/or spring? 21. Can I polish, grind, shave or dremel the internal components of my gun? 4. Sights: 01. Can I add flourescent paint to my OFM front sight? 02. Can I use fibre optic sights on my Glock? (See July 2006 Handgun Rule Interpretations - "Any Open Sights" now permitted) 5. Grips and Tape On Grips: 01. Can I add grip tape to my thumb safety, slide and/or trigger guard? 02. Can I deactivate the grip safety on my Springfield XD using tape? 03. Can I use a Hogue "handall" grip sleeve on my gun? 04. Can I install laser equipped grips if I don't switch them on? 05. Can I stipple the grip of my gun with a soldering iron or similar? 06. Can I grind down my OFM grips and use SuperGlue to add grains of sand or fairy dust instead of grip tape? 07. Can I add resin to my frame to make the grip fit my hand better? 6. Miscellaneous: 01. Can I use a Glock 17C with a regular Glock 17 barrel? 02. Can I use my Glock 18 in Production Division if I use it in Semi-Auto mode? 03. Can I use my Kimber 45ACP in Production Division? 04. Can I install a Lasermax in my Glock, if I don't switch it on? 05. Can I use aftermarket screws, pins or other fasteners on my gun? 06. Can I add "Hello Kitty" stickers on my grip? 07. Can I have two fluffy dice hanging off my front sight? 08. Can I colour-coordinate my gun to match my Kate Spade handbag and Manolo Blahnik shoes, dahhhling? 09. Can I ....... ? NO! (Non, 不, Nein, いいえ, Hindi, Nr, αριθ, Nie, Não, Нет, 아니다, Nee, Không, Nei, Ei, Nej, Le, كَلِمَةٌ, Ne, Tidak, ไม่, Nem, Yok & NFW!) (But I've got $10 that says there'll still be questions!) Quelle: Vince Pinto am 18 Aug 2006, 10:52 pm in "Production Division FAQ - Revisited, READ THIS FIRST!!!"; http://ipsc.invisionzone.com/index.php?showtopic=4094 (Man muß allerdings registriert und angemeldet sein, um's lesen zu können.) Siehe Punkt 5.05! @Moderatoren: Nachdem ich des Obige scho mehrmals posten mußte, könntet Ihr des net mal pinnen!?! Grüße Iggy
Horst Wittmann Posted October 4, 2008 Posted October 4, 2008 Quelle: Vince Pinto am 18 Aug 2006, 10:52 pm in "Production Division FAQ - Revisited, READ THIS FIRST!!!"; http://ipsc.invisionzone.com/index.php?showtopic=4094(Man muß allerdings registriert und angemeldet sein, um's lesen zu können.) Siehe Punkt 5.05! @Moderatoren: Nachdem ich des Obige scho mehrmals posten mußte, könntet Ihr des net mal pinnen!?! Grüße Iggy Fibre-Optic-Sights sind ja wohl mittlerweile erlaubt, wenn der Schlitten ztur Montage nicht verändert werden muß.., Horst
Iggy Posted October 4, 2008 Posted October 4, 2008 Fibre-Optic-Sights sind ja wohl mittlerweile erlaubt, wenn der Schlitten ztur Montage nicht verändert werden muß..,Horst Freilich - steht ja auch genauso drinnen!
Horst Wittmann Posted October 4, 2008 Posted October 4, 2008 Freilich - steht ja auch genauso drinnen! Wennu recht hast - hasu recht! Horst
Moon Posted October 5, 2008 Posted October 5, 2008 ...wie sieht es mit Skatebordtape aus? Das geht doch oder? Dieser Griffpariser für die Glock ist ja auch nicht verboten oder? ... Ja, das ist erlaubt. Allerdings nur an bestimmten Stellen des Griffstückes. http://www.ipsc.org/pdf/RulesHandgunInterp200706.pdf DVC
otto Posted October 5, 2008 Posted October 5, 2008 "Griffpariser" (Hogue-Sleeve) ist verboten. DVC otto
Horst Wittmann Posted October 6, 2008 Posted October 6, 2008 "Griffpariser" (Hogue-Sleeve) ist verboten.DVC otto und - gestippelte Griffschalen vom OFM - sind wohl (ich bin vorsichtiger geworden) erlaubt. Siehe SIG-Allround. Horst
Iggy Posted October 6, 2008 Posted October 6, 2008 und -gestippelte Griffschalen vom OFM - sind wohl (ich bin vorsichtiger geworden) erlaubt. Siehe SIG-Allround. Horst Hmhmmmm, ge - nau! Und ab hier wird's dann langsam pervers: Nicht umsonst K****n mich ebensolche Situationen als RO total an: http://forum.waffen-online.de/index.php?sh...t&p=1025112 Grüße Iggy
bulli357 Posted October 6, 2008 Posted October 6, 2008 erklärt mir bitte mal eine was mit stippeln gemeint ist? danke
Iggy Posted October 6, 2008 Posted October 6, 2008 erklärt mir bitte mal eine was mit stippeln gemeint ist?danke Mittels heißer Lötkolbenspitze den Kunststoffgriff bearbeiten (=heiße Spitze ins Material drückem und wieder rausziehen: Du hast dann 'ne Vertiefung und rund um diese noch einen meist recht scharfkantigen Wall, aufgeworfen durch die den geschmolzenen Kst. verdrängende Lötkolbenspitze). Na ja, so bearbeitest' halt flächenbdeckend den ganzen Griff. Das Stippeln macht schon tierisch griffig! ;-))) ... kannst alternativ latürnich auch einen heißgemachten Nagel oder sonstwas nehmen ... Grüße Iggy
bulli357 Posted October 6, 2008 Posted October 6, 2008 Mittels heißer Lötkolbenspitze den Kunststoffgriff bearbeiten (=heiße Spitze ins Material drückem und wieder rausziehen: Du hast dann 'ne Vertiefung und rund um diese noch einen meist recht scharfkantigen Wall, aufgeworfen durch die den geschmolzenen Kst. verdrängende Lötkolbenspitze). Na ja, so bearbeitest' halt flächenbdeckend den ganzen Griff. Das Stippeln macht schon tierisch griffig! ;-))) ... kannst alternativ latürnich auch einen heißgemachten Nagel oder sonstwas nehmen ... Grüße Iggy ok das hab ich verstanden danke und das bringt es?
Iggy Posted October 6, 2008 Posted October 6, 2008 ok das hab ich verstanden danke und das bringt es? Das Stippeln macht schon tierisch griffig! ;-)))
Kaiser Posted October 6, 2008 Posted October 6, 2008 Hmhmmmm, ge - nau! Und ab hier wird's dann langsam pervers:Nicht umsonst K****n mich ebensolche Situationen als RO total an: http://forum.waffen-online.de/index.php?sh...t&p=1025112 Grüße Iggy Das ist doch schon verückt, selbst machen verboten, von Werk aus erlaubt. Woher soll ich als RO wissen ob die Griffschalen gekauft oder selbstgemacht sind?? Kaiser
Iggy Posted October 7, 2008 Posted October 7, 2008 Das ist doch schon verückt, selbst machen verboten, von Werk aus erlaubt.Woher soll ich als RO wissen ob die Griffschalen gekauft oder selbstgemacht sind?? Kaiser GENAU DAS ist doch das Perverse! Net mal Vince Pinto kann das rausfinden!;-))) THE - O - RE - TISCH müßte man sich als RO vom Schützen per Rechnung oder Ähnlichem nachweisen lassen, daß das "ab Werk" so ist oder OFM-Zubehör. Grüße Iggy p.s. Konsequenz: Mittlerweile isses vielen ROs scheißegal wie die Production-Waffen beieinader sind! Bei der DM kamen Schützen mit Magazinen und/oder Kanone vor'm Bauch, fast wie bei "Open", gestippelten Griffen, selbst bei Waffen, wo's das definitiv net "ab Werk" gibt (Glock!) ...
Guest Posted October 7, 2008 Posted October 7, 2008 Bei der DM kamen Schützen ... gestippelten Griffen... Einem on dit zu Folge sollen auch 2 HK Pistolen mit gestippeltem Griff und leichtem Funnel à la Tafo Stock2 als "PD legal" abgenickt worden sein, min. 1 davon Werksschütze, mit der Begründung: diese Waffe würde demnächst so auf die Liste kommen und dies sei kurzfristig telefonisch mit VP so abgesprochen. Habe es leider auch nur aus 2. Hand, aber mich wundert nichts mehr
Schwichtenberg Posted October 8, 2008 Posted October 8, 2008 wenn das so weitergeht und nichts passiert, wird der "equipement check" künftig so aussehen.... .....anstatt vielleicht so sicher wird dann da "vince pinto" genau in der mitte sitzen, und die ganzen fummler, feiler und stippler werden ihr equipement sheet nach der waffenkontrolle da abholen dürfen.... achso....das war nur ein kleiner tagtraum.... B)
Recommended Posts
Archived
This topic is now archived and is closed to further replies.